Auteur Topic: BC016/BC216  (gelezen 7060 keer)

alphavisionoloog

  • Volledig lid
  • ****
  • Berichten: 91
  • eerst denken dan doen!
    • Bekijk profiel
  • Functie: Projectleider
BC016/BC216
« Gepost op: dinsdag 6 augustus 2013, 10:58 »
Kan iemand mij vertellen wat de default installateur codes zijn van de LST BC016 en de BC216?
Voor zover ik het in de manual kan terugvinden moet dat 99999 zijn, kan iemand dit bevestigen?

Alvast bedankt!

helldog2004

  • Aspirant
  • **
  • Berichten: 18
  • Safety begins with yourself
    • Bekijk profiel
    • All Above Security
  • Bedrijf: All Above Security
  • Functie: Evenementen / stewart / portier / persoons / surveillant / straatcoach / millitair
Re: BC016/BC216
« Reactie #1 Gepost op: zaterdag 31 augustus 2013, 16:04 »
5.3 Entering and exiting authorization level 3

In order to access authorization level 3 from level 1, enter the 5-digit installer code for the control panel(during the first commissioning, enter: "99999") in the same way that is described in the Chapter enti-tled "Entering and exiting authorization level 2" in Part A of the Series BC016 User Manual. [Installer level] will be shown on the display as confirmation of successful entry, and the 'Authorization' LEDwill flash.

Depending on how parameters have been set, transmitting devices or actuations may also be automati-cally disabled when authorization level 3 is entered. Devices that were activated earlier, however, willnot be disabled by this. These devices will be re-enabled automatically when you return to authoriza-tion level 1. Please note the comments regarding authorization level 2 in Part A of the Series BC016User Manual.

If the installer code is entered incorrectly 5 times consecutively, entry of the installer code will be pre-vented for 15 minutes.To return to authorization level 1, switch to main menu item [Exit authorization?] either by using themenu or by quick-operation (“esc” button) and confirm it with the '



' button. [User level exited] ap- pears on the display and the green 'Authorization' LED in the display field of the control panel goes out.If parameters have been changed, these will now be transferred into a permanent memory ([Save config. please wait...] is shown in the display), and the control panel will do a restart – the new parameters will be effective for the control panel only after this occurs.

When a restart occurs, all existing alarms, faults, etc. will be canceled, similar to what occurs whenthe 'RESET' button (reset FDCP) on the control unit of the control panel is pressed.

Authorization level 3 is time-monitored: If no operation has occurred for 10 minutes, the control panelautomatically returns to authorization level 1. All changes in the parameters, which have been made upto that point in time, will be lost at that moment. An acoustic signal will sound as a warning 1 minute prior to automatically exiting authorization level 3.The installer code is set by the actual authorized installer (see from page 51 in Chapter 7.5: "Changingthe installer code – submenu item [Cha. inst.code:]"), and it is in his or her best interest that he or shekeep the code confidential. What to do in the event the installer code is lost can be found starting on page 90 in Chapter 11.2: "Lost installer code".

Ik hoop dat uw Engels redelijk goed is, maar hier is uw confirmatie m.b.t. de installateurs code!
Vriendelijke groet,
Henk
Safety begins with yourself!!

alphavisionoloog

  • Volledig lid
  • ****
  • Berichten: 91
  • eerst denken dan doen!
    • Bekijk profiel
  • Functie: Projectleider
Re: BC016/BC216
« Reactie #2 Gepost op: dinsdag 8 oktober 2013, 22:01 »
Beste Henk,

Bedankt voor uw reactie, heeft u ook de tekst uit het hoofdstuk (of waar zou ik het kunnen vinden) "lost installer code"(genoemd op de laatste regel)

Alvast bedankt!